Views: 0 Author: Site Editor Publish Time: 2026-10-27 Origin: Site
A sanitary napkin needs to remain in the correct position during walking, sitting, and other everyday movements. If the pad shifts or bunches up, it may become uncomfortable and fail to provide the protection intended by its design. However, keeping the pad firmly attached is only half the challenge. Once it is time for replacement, the user should be able to remove it without damaging the underwear or leaving an unwanted sticky residue.
This balance is the main reason positioning adhesive is used in sanitary napkins. Applied to the back of the product, this specialized adhesive provides temporary attachment to underwear fabric while allowing the pad to be removed after use. Unlike construction adhesives, which hold product layers together, positioning glue must maintain sufficient adhesion during wear and release from the textile when the pad is removed.
For sanitary napkin manufacturers, selecting the right adhesive requires careful consideration of initial tack, peel strength, cohesive stability, and coating consistency. These properties determine how reliably the pad stays in place and how cleanly it can be removed from different underwear materials.
Position glue, more commonly referred to as sanitary napkin positioning adhesive, is a pressure-sensitive adhesive applied to designated areas on the back of a sanitary pad or panty liner. Its purpose is to hold the product against the user's underwear during wear without creating a permanent bond.
A pressure-sensitive adhesive develops adhesion when the surfaces are brought into contact under suitable pressure. Unlike conventional hot melt construction adhesives, its function is not simply to solidify into a permanent structural joint. The adhesive layer must retain enough tack at normal use temperatures to grip the textile while maintaining the internal strength needed for controlled removal.
In a typical sanitary napkin structure, the positioning adhesive is located on the garment-facing side of the backsheet. Before use, a release liner or suitable protective material covers the adhesive and prevents unintended attachment during packaging and storage.
When the protective liner is removed, the adhesive is exposed and the sanitary napkin can be pressed into position against the underwear. The quality of this attachment depends on the adhesive formulation, coating pattern, textile surface, and pressure applied during placement.
Cheshire's SBC hot melt positioning adhesive for sanitary napkins is designed for temporary attachment applications involving sanitary pads, panty liners, and related hygiene products. Its pressure-sensitive formulation focuses on maintaining positioning strength while supporting clean removal from suitable textile surfaces.
The holding function of a sanitary pad positioning adhesive depends on the interaction between the adhesive layer and the underwear fabric. When the pad is pressed into place, the adhesive contacts the textile surface and establishes a bond through its pressure-sensitive properties.
A successful bond must resist the forces generated during normal movement. Walking, bending, and changing posture can create small pulling and sliding forces between the sanitary napkin and the fabric. If the adhesive has insufficient holding power, the pad may gradually move away from its original position.
However, the adhesive is not the only factor determining whether a pad stays securely in place. The pad's overall shape, the placement of its adhesive strips, the design of its wings, and the fit of the underwear can all influence positioning.
For this reason, increasing adhesive strength alone is not always the best way to improve performance. If the adhesive becomes excessively aggressive, removing the pad may become difficult, particularly on delicate fabrics. The more effective approach is to achieve the required holding strength while maintaining controlled peel behavior.
This is why positioning adhesives are formulated differently from many permanent bonding products. Their purpose is to provide reliable temporary fixation, not the strongest possible bond under every condition.
The most important performance challenge in sanitary napkin positioning is achieving sufficient adhesion during use without creating excessive removal force or adhesive transfer.
Three properties deserve particular attention: initial tack, peel strength, and cohesive strength. These characteristics influence different stages of the product's use and should be evaluated together.
Initial tack describes the ability of the adhesive to establish contact and grip a surface under relatively light pressure. For sanitary napkins, appropriate initial tack helps the pad remain in position after the user removes the release liner and presses the product onto the underwear.
If the adhesive has insufficient initial tack, it may not establish adequate contact with the textile. This can be particularly noticeable on fabrics with uneven surfaces or when the user applies only light pressure.
Higher tack can improve initial attachment in some situations, but it does not automatically guarantee better overall performance. Adhesive behavior after prolonged contact and during removal must also be considered.
Peel strength describes the force required to separate the adhesive from a surface under defined testing conditions. For sanitary napkins, this property influences how easily the product can be removed after use.
If peel strength is too low, the pad may detach during movement. If it is excessively high, removal can become difficult and may place unnecessary stress on the underwear fabric.
The required peel strength should reflect the intended garment materials and use conditions. A suitable formulation maintains enough attachment strength for normal movement without requiring excessive force during removal.
Cohesive strength refers to the adhesive's internal resistance to separation or deformation. It is especially important for removable applications because an adhesive may stick strongly to a textile yet split within its own layer when the pad is removed.
When cohesive strength is insufficient relative to the forces acting on the bond, part of the adhesive may remain on the underwear rather than staying attached to the sanitary napkin.
This is one reason pressure sensitive adhesive for sanitary pads must be designed around more than surface tack. Clean removal depends on the relationship between adhesion to the textile, adhesion to the pad backing, and the internal strength of the adhesive layer.
The main performance relationships can be summarized as follows:
Adhesive Property | Required Function | Potential Problem When Unbalanced |
|---|---|---|
Initial tack | Establishes attachment when the pad is positioned | Poor initial grip or unwanted excessive stickiness |
Peel strength | Maintains attachment while allowing removal | Pad shifting or difficult peeling |
Cohesive strength | Keeps the adhesive layer intact during removal | Adhesive transfer or sticky residue |
Temperature stability | Supports performance across expected conditions | Changes in tack, flow, or removal behavior |
Coating consistency | Provides predictable attachment across the pad | Uneven holding force or localized residue |
Underwear fabrics differ considerably in fiber composition, surface structure, elasticity, and finishing treatments. These differences can change how a positioning adhesive establishes contact and how the bond behaves during removal.
Cotton fabrics often have textured fiber surfaces that differ from those of smooth synthetic textiles. Polyester, nylon, and blended materials may present different surface characteristics, while certain stretch fabrics contain elastane and can deform significantly during peeling.
Consequently, an adhesive that performs well on one textile cannot automatically be expected to produce identical peel strength on another.
Cotton textiles typically have a fibrous surface that can provide multiple contact points for the adhesive. However, weave structure, fabric thickness, surface treatments, and laundering history may influence the actual bond.
An adhesive with strong wetting behavior may grip the fabric effectively, but excessive penetration or unsuitable cohesive properties could make clean removal more difficult. Performance should therefore be evaluated using representative cotton fabrics rather than assuming that all cotton underwear behaves the same way.
Synthetic fabrics may have smoother surfaces or different finishing treatments compared with cotton. The adhesive must establish sufficient contact with these materials to provide reliable positioning.
Fabric elasticity also affects removal behavior. When a stretch textile deforms as the sanitary napkin is peeled away, the apparent removal force can change. A formulation that releases smoothly from a relatively stable fabric may behave differently on a highly elastic textile.
Cheshire's positioning adhesive range addresses temporary bonding requirements for hygiene applications. Its featured SBC-based product is intended for use with a variety of textile surfaces, but manufacturers should still evaluate the specific fabric types relevant to their target markets.
A meaningful evaluation should include representative fabrics rather than relying on a single standard substrate. Manufacturers may need to compare adhesion to cotton, polyester, nylon, and selected blends, depending on the positioning requirements of the finished product.
The contact time between the adhesive and textile also matters. A pad removed immediately after placement may behave differently from one that has remained attached for several hours under body warmth and movement.
By evaluating these variables together, manufacturers can identify a sanitary napkin adhesive that provides a suitable balance of holding power and removal performance for the intended products.
The positioning adhesive is typically applied to the garment-facing backsheet in designated coating areas. The layout and dimensions of these areas determine where the pad attaches to underwear and influence how the holding force is distributed across the product.
For many sanitary napkin designs, the adhesive is deposited in longitudinal strips or other controlled patterns. The selected geometry should provide appropriate attachment without covering unnecessary areas of the backsheet.
Slot coating is an established method for applying hot melt positioning adhesives. The adhesive is heated to the appropriate processing temperature and delivered through a coating head that deposits a controlled layer onto the substrate.
A stable coating process helps maintain consistent adhesive placement, width, and coating weight. These characteristics are important because variations in the adhesive pattern can change how the finished sanitary napkin attaches to fabric.
Cheshire's featured sanitary napkin hot melt adhesive is specified for slot coating at an application temperature of 150–170°C, with a softening point of 95 ± 5°C. Its SBC-based formulation is designed for pressure-sensitive positioning applications.
The processing temperature influences viscosity and coating stability, but it should not be confused with the temperature at which the finished pad is used. The hot melt is applied during manufacturing and subsequently cools to form the pressure-sensitive adhesive layer.
After coating, the adhesive is normally protected with release paper or another suitable liner material. This protective layer prevents the adhesive from attaching to unintended surfaces before the sanitary napkin is used.
Release liner compatibility is important because the liner must remain attached during packaging and handling yet separate without removing or damaging the adhesive coating.
If release force is too high, the adhesive layer may be disturbed during liner removal. If release force is too low, the liner may detach prematurely during converting or packaging.
The liner's release characteristics, coating uniformity, and the adhesive's own cohesion should therefore be evaluated together.
A simplified production sequence is:
Backsheet Preparation → Hot Melt Slot Coating → Release Liner Application → Cooling → Converting and Packaging
The exact sequence depends on the converting line and product construction. The main objective is to preserve a stable, accurately positioned adhesive layer that remains protected until the product is ready for use.
Problems involving sanitary pad back adhesive often become apparent during consumer use, but their causes may originate in material selection or coating conditions during manufacturing.
Identifying the specific failure helps determine whether the issue is related to adhesive formulation, substrate compatibility, or the coating process.
Poor positioning may result from insufficient tack, inadequate coating weight, unsuitable adhesive placement, or limited contact between the adhesive and the underwear fabric.
However, the relationship between the pad and textile must also be considered. Wrinkled fabric, loose-fitting underwear, or substantial movement can affect how the pad remains positioned.
Manufacturers should examine whether the adhesive is making adequate contact with the target fabric and whether the coating pattern provides sufficient holding force across the relevant areas.
Residue problems occur when adhesive transfers to the textile during removal. This may be associated with unsuitable cohesive strength, excessive adhesion to the fabric, thermal exposure, or other formulation-related factors.
The failure should be examined carefully. Adhesive splitting within its own layer may suggest a different cause from the adhesive separating from the pad backing.
Improving clean removal may require adjusting the formulation, coating weight, or the relationship between the adhesive and backsheet material. Simply reducing tack can make the pad easier to remove but may also reduce positioning reliability.
High peel resistance can create inconvenience and may place additional stress on delicate underwear fabrics. This can occur when the adhesive develops excessive attachment under the actual contact time and temperature conditions.
Manufacturers should evaluate removal after realistic periods of contact rather than relying only on immediate peel testing. Testing should also account for different fabric types because the same adhesive may behave differently on cotton, nylon, and blended textiles.
Irregular coating can create areas with too little adhesive and other areas with excessive buildup. This may produce inconsistent positioning and removal behavior across the finished product.
Potential causes include unsuitable viscosity, unstable adhesive flow, coating-head contamination, or incorrect equipment adjustment. Temperature management and routine applicator maintenance are therefore important.
Where production issues persist, Cheshire provides technical support for hot melt adhesive applications, including assistance with application requirements and equipment-related performance concerns.
A reliable selection process should evaluate the complete positioning system rather than measuring adhesive tack alone.
The manufacturer's testing program should reflect the intended sanitary napkin design, coating method, garment materials, and expected storage conditions.
Testing should include fabric types relevant to the target product market. Peel measurements should be performed under defined conditions so that results can be compared meaningfully.
Relevant test variables include contact pressure, dwell time, peel angle, peel rate, and temperature. Because these variables influence measured adhesion, comparative testing must use consistent procedures.
A strong positioning bond is of limited value if removing the pad leaves adhesive on the underwear. Samples should be examined after removal to determine whether the adhesive remains on the pad backing or transfers to the textile.
Testing should consider both immediate removal and removal after a representative period of contact. Where appropriate, different temperatures can be used to evaluate how the formulation behaves under warmer or cooler conditions.
A formulation must also perform reliably during manufacturing. The adhesive should flow consistently through the coating equipment and form the intended pattern without excessive smearing, buildup, or irregular distribution.
The interaction between the adhesive and release liner should be checked as well. If the liner releases inconsistently, the finished product may be difficult to use even when adhesion to underwear is satisfactory.
A practical evaluation can be organized around the following criteria:
Test Area | Main Question |
|---|---|
Initial tack | Does the pad attach reliably with normal placement pressure? |
Peel performance | Can the pad be removed without excessive force? |
Residue inspection | Does the adhesive remain on the pad after removal? |
Fabric compatibility | Is performance acceptable across representative underwear materials? |
Storage stability | Does the adhesive maintain suitable behavior after expected storage conditions? |
Coating quality | Can the production line apply the adhesive consistently? |
Release liner performance | Does the liner protect the adhesive and remove cleanly? |
For manufacturers developing new feminine hygiene products, an adhesive supplier's ability to respond to these test results is important. An existing formulation may satisfy the requirements, but some projects need adjustments to achieve the desired balance between tack, peel behavior, and coating performance.
Cheshire's custom adhesive formulation services allow manufacturers to evaluate standard adhesive samples and provide feedback from their own production environments. Where necessary, formulation development can address specific processing or performance requirements.
This approach is particularly useful when a sanitary napkin design incorporates an unusual backsheet, a different adhesive strip pattern, or a target garment material that requires additional testing.
A sanitary napkin should stay in place without making removal an unpleasant experience. Achieving both outcomes requires more than a highly tacky glue. The right positioning adhesive must attach reliably to underwear, maintain sufficient holding power during movement, and release cleanly when the pad is replaced.
These are the requirements behind Cheshire's SBC hot melt positioning adhesive for sanitary napkins. Designed for back-strip positioning applications, it combines pressure-sensitive adhesion with the cohesive properties needed for controlled removal. For sanitary napkin manufacturers evaluating different fabrics, coating patterns, or production conditions, Cheshire can provide samples and formulation support to help identify a suitable solution. Share your product and coating requirements through our contact page to begin a practical discussion about your next production trial.
Positioning adhesive is applied to the back of sanitary napkins and panty liners to help them remain attached to underwear during use. It provides temporary pressure-sensitive adhesion while allowing the product to be removed and replaced.
Excessive adhesion can make a pad difficult to remove and may increase the risk of fabric stress or unwanted adhesive transfer. A suitable positioning adhesive needs sufficient holding power during use while maintaining controlled peel behavior during removal.
Residue can occur when the adhesive transfers to the textile instead of remaining attached to the pad backing. Contributing factors may include the adhesive's cohesive properties, attachment to the fabric, contact time, temperature, and coating weight.
Positioning adhesives can be formulated for cotton, polyester, nylon, and other textile materials, but performance may vary with fabric structure, surface treatment, and elasticity. Manufacturers should test representative fabrics to evaluate holding strength and clean removal.
Positioning adhesive provides temporary attachment between a hygiene product and another surface, such as underwear fabric. Construction adhesive is primarily used to join structural layers within the product. Because their functions differ, the required tack, peel strength, and cohesive behavior are not necessarily the same.